Medion GoPal User Manual Page 61
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation using the voice command function
Enter coordinates
Say Coordinates to enter the destination using its coordinates. Any additional entries are made
manually.
Load tour
Say Load tour. The selection menu Load tour is opened. Say the desired entry in this menu to load
the corresponding tour. Say one of the following options:
Say Yes to start tour calculation.
Say Delete to delete the current tour.
Say Rename to rename the current tour. Any additional entries are made manually.
Operation in the map view
In the map view you have the following options for adjusting the display:
By saying Zoom in, you can increase the map’s size and the current zoom level.
By saying Zoom out, you can reduce the map’s size and the current zoom level.
Using the voice command Centre (alternatively: centre map), adjust the map section so that your
current position is displayed in the centre.
If required, you can change the display mode of the map in the following ways:
By saying (Display) compass (alternatively: (Display) Compass view/GPS view) you can open
the compass display.
Using the voice commands (Display) split-screen, Map only, Map view and Map only, switch be-
tween the respective display options.
Use the voice command (Show) Arrow view (alternatively: (Show) Manoeuvre view, (Show) Ar-
row) to activate arrow view in the display.
Use the voice command No map (alternatively: Map off/switch off/hide) to deactivate map view
in the display.
Use the voice command (Show) 3D (alternatively: (Show) 3D display, (Show) 3D view, (Show
3D map/map view) to activate the 3D map display (if available for your device).
Use the voice command (Show) 2D (alternatively: (Show) 2D view/2D display/2D map, (Show)
two-dimensional view/display/map) to activate the normal two-dimensional map display.
Use the voice command (Show) North (alternatively: (Show) 2D north/North view/North orienta-
tion, Northways) to activate 2D map display with north orientation.
Use the voice command (Show) Map in direction of travel (alternatively: (Show) in direction of
travel, (Show) view/orientation in direction of travel) to activate orientation of the map in the di-
rection of travel.
Use the voice command Optimised map (alternatively: optimise map, Optimised (2D) map orien-
tation, Optimised orientation) to activate optimised orientation of the map.
Voice command in Current route menu
Use the voice command (Menu) Current route to open the Current route menu view. Say one of
the following options:
Traffic conditions
Say Traffic conditions to open the relevant settings menu. Further operation of this menu is carried
out manually.
57
- GoPal Navigator Version 6 1
- Contents 2
- Chapter 1: Introduction 5
- Introduction 6
- System requirements 7
- Conventions in this manual 8
- Tips and warnings 8
- Important information 9
- Trademarks 9
- Copyright and Warranty 10
- Operation in the menu view 11
- Basics of operation 12
- Operation in the map view 13
- Main menu 15
- Manual destination entry 16
- Enter address 17
- Entering the street name 18
- Home address 19
- Choose from last locations 20
- Search for point of interest 20
- Choose from favourites 21
- Calling up a favourite 22
- Deleting all favourites 22
- Editing favourites 22
- Operating the GoPal 23
- navigation software 23
- Optimising the route 24
- Changing a planned route 25
- Starting a planned route 25
- Destination from map 26
- Enter coordinates 26
- Load tour 27
- Traffic conditions 32
- Route information 33
- Avoid route 33
- Route simulation 34
- Directions 34
- Stop route guidance 34
- Travel statistics 34
- Compass 35
- Plot GPS track 36
- Save current position 36
- GoPal Navigator 6 37
- Adapting the route 38
- Adjusting the settings 39
- Adapting the map 42
- Adapting the POI settings 46
- Adapting the volume 46
- Adapting the power options 49
- Adapting the TMC settings 52
- Security 53
- FM transmitter 53
- Factory settings 54
- Voice command in main menu 58
- Route options 63
- Language and keyboard 65
- Points of interest settings 65
- Warnings and driving safety 66
- Time and units 66
- Energy options 66
- Display settings 67
- Settings assistant 67
- Initial operation 68
- Installation via memory card 69
- Transferring additional data 70
- Assistant 72
- User interface of the GoPal 73
- Volume area 74
- Setting the user language 75
- Management of GPS Tracks 78
- Changing the device name 80
Related products and manuals for Car navigation systems Medion GoPal
(96 pages)
(98 pages)
(96 pages)© 2020, manymanuals.com. All rights reserved. | 1.394 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals